View EL5167ICZ-T7_4517289.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 ? fn7365.6 el5166, el5167 1.4ghz current feedb ack amplifiers with enable the el5166 and el5167 amplifiers are of the current feedback variety and exhibit a very high bandwidth of 1.4ghz at a v = +1 and 800mhz at a v = +2. this makes these amplifiers ideal for today's high speed video and monitor applications, as well as a number of rf and if frequency designs. with a supply current of just 8.5ma and the ability to run from a single supply voltage from 5v to 12v, these amplifiers offer very high performance for little power consumption. the el5166 also incorporates an enable and disable function to reduce the supply current to 13a typical per amplifier. allowing the ce pin to float or applying a low logic level will enable the amplifier. the el5167 is offered in the 5 ld sot-23 package and the el5166 is available in the 6 ld sot-23 as well as the industry-standard 8 ld soic packages. both operate over the industrial temperature range of -40c to +85c. features ? gain-of-1 bandwidth = 1.4ghz/gain-of-2 bandwidth = 800mhz ? 6000v/s slew rate ? single and dual supply operation from 5v to 12v ? low noise = 1.7nv/ hz ? 8.5ma supply current ? fast enable/disable (el5166 only) ? 600mhz family - (el5164 and el5165) ? 400mhz family - (el5162 and el5163) ? 200mhz family - (el5160 and el5161) ? pb-free available (rohs compliant) applications ? video amplifiers ? cable drivers ? rgb amplifiers ? test equipment ? instrumentation ? current to voltage converters pinouts el5166 (8 ld soic) top view el5166 (6 ld sot-23) top view el5167 (5 ld sot-23, sc-70) top view 1 2 3 4 8 7 6 5 1 2 3 4 8 7 6 5 - + nc in- in+ vs- ce vs+ out nc 1 2 3 6 4 5 - + out vs- in+ vs+ in- ce 1 2 3 5 4 - + out vs- in+ vs+ in- data sheet september 14, 2010 caution: these devices are sensitive to electrosta tic discharge; follow proper ic handling procedures. 1-888-intersil or 1-888-468-3774 | intersil (and design) is a registered trademark of intersil americas inc. copyright intersil americas inc. 2003-2005, 2007, 2010. all rights reserved all other trademarks mentioned are the property of their respective owners.
2 fn7365.6 september 14, 2010 ordering information part number (note 1) part marking package (pb-free) pkg. dwg. # el5166isz 5166isz 8 ld soic (150 mil) m8.15e el5166isz-t7* 5166isz 8 ld soic (150 mil) m8.15e el5166isz-t13* 5166isz 8 ld soic (150 mil) m8.15e el5166iwz-t7* bapa (note 2) 6 ld sot-23 p6.064a el5166iwz-t7a* bapa (note 2) 6 ld sot-23 p6.064a EL5167ICZ-T7* bfa (note 2) 5 ld sc-70 (1.25mm) p5.049 EL5167ICZ-T7a* bfa (note 2) 5 ld sc-70 (1.25mm) p5.049 el5167iwz-t7* bara (note 2) 5 ld sot-23 p5.064a el5167iwz-t7a* bara (note 2) 5 ld sot-23 p5.064a *please refer to tb347 for detai ls on reel specifications. notes: 1. these intersil pb-free plastic packaged pr oducts employ special pb-free material se ts, molding compounds/die attach materials , and 100% matte tin plate plus anneal (e3 termination finish, which is rohs compliant and compatible with both snpb and pb-free soldering operations). intersil pb-free products are msl classified at pb-free peak reflow temperatures that meet or exceed the pb-free requirements o f ipc/jedec j std-020. 2. the part marking is located on the bottom of the part. el5166, el5167
3 fn7365.6 september 14, 2010 absolute maxi mum ratings (t a = +25c) thermal information supply voltage between v s + and v s - . . . . . . . . . . . . . . . . . . . 12.6v slewrate between v s + and v s - . . . . . . . . . . . . . . . . . . . . . . . . 1v/s maximum continuous output current . . . . . . . . . . . . . . . . . . . 50ma i out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200ma i into v in +, v in -, enable pins . . . . . . . . . . . . . . . . . . . . . . . . . 4ma pin voltages . . . . . . . . . . . . . . . . . . . . . . . . . v s - -0.5v to v s + +0.5v power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see curves storage temperature . . . . . . . . . . . . . . . . . . . . . . . .-65c to +150c ambient operating temperature . . . . . . . . . . . . . . . .-40c to +85c die junction temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . +125c pb-free reflow profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/pb-freereflow.asp caution: do not operate at or near the maximum ratings listed fo r extended periods of time. exposure to such conditions may adv ersely impact product reliability and result in failures not covered by warranty. important note: all parameters having min/max specifications are guaranteed. typical values are for information purposes only. u nless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: t j = t c = t a electrical specifications v s + = +5v, v s - = -5v, r f = 392 for a v = 1, r f = 250 for a v = 2, r l = 150 , t a = +25c unless otherwise specified. parameter description conditions min typ max unit ac performance bw -3db bandwidth a v = +1 1400 mhz a v = +2 800 mhz bw1 0.1db bandwidth a v = +2 100 mhz sr slew rate v o = -2.5v to +2.5v, a v = +2 4000 6000 v/s t s 0.1% settling time v out = -2.5v to +2.5v, a v = -1 8 ns e n input voltage noise 1.7 nv/ hz i n - in- input current noise 19 pa/ hz i n + in+ input current noise 50 pa/ hz dg differential gain error (note 3) a v = +2 0.01 % dp differential phase error (note 3) a v = +2 0.03 dc performance v os offset voltage -5 -0.5 5 mv t c v os input offset voltage temperature coefficient measured from t min to t max 3.52 v/c r ol transimpedance 0.5 1.1 2.5 m input characteristics cmir common mode input range (guaranteed by cmrr test) 3 3.3 v cmrr common mode rejection ratio 52 57 66 db -icmr - input current common mode rejection -1 0.7 1 a/v +i in + input current -25 0.7 25 a -i in - input current -25 8.5 25 a r in input resistance 50 130 250 k c in input capacitance 1.5 pf output characteristics v o output voltage swing r l = 150 to gnd 3.6 3.8 4.1 v r l = 1k to gnd 3.8 4.0 4.2 v i out output current r l = 10 to gnd 110 160 200 ma el5166, el5167
4 fn7365.6 september 14, 2010 supply i son supply current - enabled no load, v in = 0v 7.5 8.5 9.3 ma i soff+ supply current - disabled no load, v in = 0v 1 4 25 a i soff- supply current - disabled no load, v in = 0v -25 -14 -1 a psrr power supply rejection ratio dc, v s = 4.75v to 5.25v 70 50 db -ipsr - input current power supply rejection dc, v s = 4.75v to 5.25v -0.5 0.2 1 a/v enable (el5166 only) t en enable time 170 ns t dis disable time 1.25 s i ihce ce pin input high current ce = v s +0-1a i ilce ce pin input low current ce = v s - 1 13 25 a v ihce ce input high voltage for power-down v s + -1 v v ilce ce input low voltage for power-down v s + -3 v note: 3. standard ntsc test, ac signal amplitude = 286mv, f = 3.58mhz. electrical specifications v s + = +5v, v s - = -5v, r f = 392 for a v = 1, r f = 250 for a v = 2, r l = 150 , t a = +25c unless otherwise specified. (continued) parameter description conditions min typ max unit typical performance curves figure 1. frequency respon se as the function of r f figure 2. frequency respo nse as the function of the gain 0 3 4 5 -5 -4 -3 -2 -1 1 2 normalized magnitude (db) 100k 10m 100m 1g frequency (hz) 1m r f = 392 r f = 662 r f = 511 r f = 608 r f = 698 r f = 806 r f = 900 r f = 1k v cc = 5v v ee = -5v r l = 150 r f = 368 100k 10m 100m 1g frequency (hz) 1m 4 3 2 1 0 -3 -5 -1 -2 -4 normalized magnitude (db) -6 r g = 43 v cc = 5v v ee = -5v r l = 150 r f = 392 r g = 93 r g = 186 r g = 392 el5166, el5167
5 fn7365.6 september 14, 2010 figure 3. freqency response vs c in figure 4. non-inverting frequency response for various c in - (6 ld sot-23) figure 5. inverting frequency response for gain of 1 and 2 figure 6. rise and fall time (6 ld sot-23) figure 7. frequency response as the function of the power supply voltage figure 8. inverting amplifier, frequency response as the function of v cc , v ee gain - 1 typical performance curves (continued) c = 0p 5 4 3 2 1 -2 -4 0 -1 -3 normalized magnitude (db) -5 100k 1m 10m 100m 1g frequency (hz) c = 1p c = 1.5p c = 2.5p c = 4.7p 0 4 -4 -2 2 normalized gain (db) 100k 10m 100m 1g frequency (hz) 1m c = 4.7p c = 2.5p c = 0 c = 1.5p v cc =+v v ee =-5v rl=150w v cc = +5v v ee = -5v r l = 150 r f = r g = 392 c = 1p -1 3 -5 -3 1 5 4 3 2 1 0 -3 -5 -1 -2 -4 normalized gain (db) -6 1m 100m 1g frequency (hz) 10m v cc , v ee = 5v r f = 220 r g = 220 r f = 220 r g = 100 0.5v/div 2ns/div 4 3 2 1 0 -3 -5 -1 -2 -4 normalized gain (db) -6 100k 1m 10m 100m 1g frequency (hz) r l = 150 r f = 300 r g = 300 3.0v 6.0v 5.0v 2.5v 1m 100m 1k frequency (hz) 10m 4 3 2 1 0 -3 -5 -1 -2 -4 normalized gain (db) -6 r l = 150 r f = 220 r g = 220 2.5v 3.5v 6.0v 5.0v el5166, el5167
6 fn7365.6 september 14, 2010 figure 9. transimpedance magnitude and phase as the function of the frequency figure 10. closed loop output impedance vs frequency (6 ld sot-23) figure 11. psrr +5v figure 12. psrr -5v figure 13. common mode rejection as the function of the frequency and power supply voltage figure 14. large signal response typical performance curves (continued) -90 -270 -180 0 magnitude (db) 100k 10m 100m 1g frequency (hz) 1m v cc , v ee = 2.5v 10k 100 1k 100k 5.0v 2.5v 6.0v 5.0v 2.5v phase ( ) 10 10m 100m 1 z out ( ) 10k 1m 10m frequency (hz) 100k 100m v cc , v ee = 5v gain = 2 0 10 20 30 40 50 60 70 psrr (v cc ) (db) 80 100 10k 1m 10m 100m frequency (hz) 1k 100k v cc = 5v v ee = -5v r l = 150 r f = 402 r g = 402 0 10 20 30 40 70 50 60 psrr (v ee ) (db) 80 100 10k 1m 10m 100m frequency (hz) 1k 100k v cc = 5v v ee = -5v r l = 150 r f = 402 r g = 402 -30 0 -80 -70 -60 -50 -40 -20 -10 cmrr (db) 1k 1m 10m 300m frequency (hz) 10k r f = r g = 250 100m 5.0v 6.0v 100k 3.5v 2.5v -2 1 2 3 -7 -6 -5 -4 -3 -1 0 normalized magnitude (db) 100k 10m 100m 1g frequency (hz) 1m v cc = 5v v ee = -5v r l = 150 gain = 2 load = 150 input level = 3v p-p el5166, el5167
7 fn7365.6 september 14, 2010 figure 15. t out vs frequency and v cc , v ee figure 16. distortion vs frequency figure 17. harmonic distortion vs supply voltage figure 18. harmonic distortion vs supply voltage figure 19. distortion vs power supply voltage figure 20. distortion vs power supply voltage (el5166) typical performance curves (continued) 2 . 0 100 1.0 400 500 600 700 800 900 1000 frequency (hz) v outp-p (v) 0 300 200 v cc , v ee = 5v 3v 2.5v 1.5 0.5 6v -50 -55 -60 -85 1 6 11 16 26 36 frequency (mhz) distortion (db) 31 21 -70 -65 -75 -80 thd second harmonic third harmonic v cc , v ee = 5v, r l = 150 , a v = 2 -74 -76 -78 -80 -82 -86 5678 10 12 total supply voltage (v) distortion (db) 11 9 -84 thd hd2 hd3 f = 1mhz, r l = 150 , a v = 2, v op-p = 2v 10 0 -10 -20 -30 -90 5678 10 12 total supply voltage (v) distortion (db) 11 9 -50 hd2 -40 -60 -70 -80 f = 5mhz, r l = 150 , a v = 2, v o = 2v p-p hd3 thd -50 -55 -60 -90 5678 10 12 total supply voltage (v) distortion (db) 11 9 -70 -65 -75 -80 -85 f = 10mhz, r l = 150 , a v = 2 v o = 2v p-p thd second harmonic third harmonic -50 -55 -60 -80 5678 10 12 total supply voltage (v) distortion (db) 11 9 -70 -65 -75 f = 20mhz, r l = 150 , a v = 2 v o = 2v p-p thd third harmonic second harmonic el5166, el5167
8 fn7365.6 september 14, 2010 figure 21. turn-on time (el5166) figure 22. turn-off time (el5166) figure 23. supply current vs supply voltage (el5166) figure 24. package power dissipation vs ambient temperature figure 25. package power dissipation vs ambient temperature typical performance curves (continued) 8.5 8.4 8.3 8.2 8.1 7.4 2.5 3.0 3.5 4.0 5.0 6.0 supply voltage (v) supply current (ma) 5.5 4.5 7.9 8.0 7.8 7.7 7.6 i s 7.5 i s - 909mw 1.4 1.2 1.0 0.8 0.6 0.2 0 0 25 50 75 100 150 ambient temperature (c) power dissipation (w) 125 85 jedec jesd51-7 high effective thermal conductivity test board 0.4 435mw ja = +110c/w so8 ja = +230c/w sot23-5/6 625mw ja = +160c/w so8 1.0 0.9 0.8 0.6 0.4 0.1 0 0 25 50 75 100 150 ambient temperature (c) power dissipation (w) 125 85 jedec jesd51-3 low effective thermal conductivity test board 0.2 0.7 0.3 0.5 391mw ja = +256c/w sot23-5/6 el5166, el5167
9 fn7365.6 september 14, 2010 pin descriptions 8 ld soic 6 ld sot-23 5 ld sot-23 pin name function equivalent circuit 1, 5 nc not connected 2 4 4 in- inverting input circuit 1 3 3 3 in+ non-inverting input (see circuit 1) 4 2 2 vs- negative supply 6 1 1 out output circuit 2 7 6 5 vs+ positive supply 85 ce chip enable circuit 3 in- in+ v s + v s - v s + v s - out v s + v s - ce el5166, el5167
10 fn7365.6 september 14, 2010 applications information product description the el5166 and el5167 are current-feedback operational amplifiers that offers a wide -3db bandwidth of 1.4ghz and a low supply current of 8.5ma per amplifier. the el5166 and el5167 work with supply voltage s ranging from a single 5v to 10v and they are also capable of swinging to within 1v of either supply on the output. because of their current-feedback topology, the el5166 and el5167 do not have the normal gain-bandwidth product associated with voltage-feedback operational amplifiers. instead, their -3db bandwidth remains relatively constant as closed -loop gain is increased. this combination of high bandwidth and low power, together with aggressive pricing make the el5166 and el5167 ideal choices for many low-power/high-bandwidth applications, such as portable, handheld, or battery-powered equipment. power supply bypassing and printed circuit board layout as with any high frequency device, good printed circuit board layout is necessary for optimum performance. low impedance ground plane construction is essential. surface mount components are recommended, but if leaded components are used, lead lengths should be as short as possible. the power supply pins must be well bypassed to reduce the risk of oscillation. the combination of a 4.7f tantalum capacitor in parallel with a 0.01f capacitor has been shown to work well when placed at each supply pin. for good ac performance, parasitic capacitance should be kept to a minimum, especially at the inverting input (see ?capacitance at the inverting input? on page 10). even when ground plane construction is used, it should be removed from the area near the inverting input to minimize any stray capacitance at that node. carbon or metal-film resistors are acceptable with the metal-film resistors giving slightly less peaking and bandwidth because of additional series inductance. use of sockets, pa rticularly for the so package, should be avoided if possible. sockets add parasitic inductance and capacitance, which will result in additional peaking and overshoot. disable/power-down the el5166 amplifier can be dis abled, placing its output in a high impedance state. when disabled, the amplifier supply current is reduced to 13a. the el5166 is disabled when its ce pin is pulled up to within 1v of the positive supply. similarly, the amplifier is enabled by floating or pulling its ce pin to at least 3v below the positive supply. for 5v supply, this means that an el5166 amplifier will be enabled when ce is 2v or less, and disabled when ce is above 4v. although the logic levels are not standard ttl, this choice of logic voltages allows the el5166 to be enabled by tying ce to ground, even in 5v sing le supply applications. the ce pin can be driven from cmos outputs. capacitance at the inverting input any manufacturer?s high-speed voltage- or current-feedback amplifier can be affected by stray capacitance at the inverting input. for inverting gains, this parasitic capacitance has little effect because the inverting input is a virtual ground. but for non-inverting gains, this capacitance (in conjunction with the feedback and gain resistor s) creates a pole in the feedback path of the amplifier. this pole, if low enough in frequency, has the same destabilizing effect as a zero in the forward open-loop response. the use of large value feedback and gain resistors exacerbates the problem by further lowering the pole frequency (increasing the possibility of oscillation). the el5166 and el5167 frequency responses are optimized with the resistor values in figure 3. with the high bandwidth of these amplifiers, these resistor values might cause stability problems when combined with parasitic capacitance, thus ground plan e is not recommended around the inverting input pin of the amplifier. feedback resistor values the el5166 and el5167 have been designed and specified at a gain of +2 with r f approximately 392 . this value of feedback resistor gives 800mhz of -3db bandwidth at a v = 2 with about 0.5db of peaking. since the el5166 and el5167 are current-feedback amplifiers, it is also possible to change the value of r f to get more bandwidth. as seen in the curve of frequency response for various r f and r g in the ?typical performance curves? on page 4, bandwidth and peaking can be easily modified by varying the value of the feedback resistor. because the el5166 and el5167 are current-feedback amplifiers, their gain-bandwidth product is not a constant for different closed-loop gains. this feature actually allows the el5166 and el5167 to maintain a reasonably constant -3db bandwidth for different gains. as gain is increased, bandwidth decreases slightly while stability increases. since the loop stability is improving with higher closed-loop gains, it becomes possible to reduce the value of r f below the specified 250 and still retain stability, resulting in only a slight loss of bandwidth with increased closed-loop gain. supply voltage range and single-supply operation the el5166 and el5167 have been designed to operate with supply voltages having a span of greater than 5v and less than 10v. in practical te rms, this means that the el5166 and el5167 will operate on dual supplies ranging from 2.5v to 5v. with single-supply, they will operate from 5v to 10v. as supply voltages continue to decrease, it becomes necessary to provide input an d output voltage ranges that can get as close as possible to the supply voltages. the el5166 and el5167 have an input range that extends to within 1.8v of either supply. so, for example, on 5v el5166, el5167
11 fn7365.6 september 14, 2010 supplies, the el5166 and el5167 have an input range which spans 3.2v. the output range of the el5166 and el5167 is also quite large, extending to within 1v of the supply rail. on a 5v supply, the output is therefore capable of swinging from -4v to +4v. video performance for good video performance, an amplifier is required to maintain the same output impedance and the same frequency response as dc levels are changed at the output. this is especially di fficult when driving a standard video load of 150 because of the change in output current with dc level. previously, good differential gain could only be achieved by running high idle currents through the output transistors (to reduce variations in output impedance.) these currents were typically comparable to the entire 8.5ma supply current of each el5166 and el5167 amplifier. special circ uitry has been incorporated in the el5166 and el5167 to reduc e the variation of output impedance with the current output. this results in dg and dp specifications of 0.01% and 0.03, while driving 150 at a gain of 2. output drive capability in spite of their low 8.5ma of supply current, the el5166 and el5167 are capable of providi ng a minimum of 110ma of output current. with so much output drive, the el5166 and el5167 are capable of driving 50 loads to both rails, making them an excellent choice for driving isolation transformers in telecommunications applications. driving cables and capacitive loads when used as a cable driver, double termination is always recommended for reflection-free performance. for those applications, the back-termination series resistor will decouple the el5166 and el5167 from the cable and allow extensive capacitive drive. ho wever, other applications may have high capacitive loads without a back-termination resistor. in these applications, a small series resistor (usually between 5 and 50 ) can be placed in series with the output to eliminate most pe aking. the gain resistor (r g ) can then be chosen to make up for any gain loss which may be created by this additional resist or at the output. in many cases it is also possible to si mply increase the value of the feedback resistor (r f ) to reduce the peaking. current limiting the el5166 and el5167 have no internal current-limiting circuitry. if the output is shorted, it is possible to exceed the absolute maximum rating for output current or power dissipation, potentially result ing in the destruction of the device. power dissipation with the high output drive capability of the el5166 and el5167, it is possible to exceed the +125c absolute maximum junction temperature under certain very high load current conditions. generally speaking, when r l falls below about 25 , it is important to calculate the maximum junction temperature (t jmax ) for the application to determine if power supply voltages, load conditions, or package type need to be modified for the el5166 and el5167 to remain in the safe operating area. these parameters are calculated as follows: where: t max = maximum ambient temperature ja = thermal resistance of the package n = number of amplifiers in the package pd max = maximum power dissipation of each amplifier in the package pd max for each amplifier can be calculated as follows: where: v s = supply voltage i smax = maximum supply current of 1a v outmax = maximum output voltage (required) r l = load resistance t jmax t max ja npd max () + = (eq. 1) pd max 2 ( v s i smax ) v s ( v outmax ) v outmax r l ---------------------------- ? + = (eq. 2) el5166, el5167
12 all intersil u.s. products are manufactured, asse mbled and tested utilizing iso9000 quality systems. intersil corporation?s quality certifications ca n be viewed at www.intersil.com/design/quality intersil products are sold by description only. intersil corpor ation reserves the right to make changes in circuit design, soft ware and/or specifications at any time without notice. accordingly, the reader is cautioned to verify that data sheets are current before placing orders. information furnishe d by intersil is believed to be accurate and reliable. however, no responsibility is assumed by intersil or its subsidiaries for its use; nor for any infringements of paten ts or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of intersil or its subsidiari es. for information regarding intersil corporation and its products, see www.intersil.com fn7365.6 september 14, 2010 typical application circuits figure 26. inverting 200ma output current distribution amplifier figure 27. fast-settling precision amplifier figure 28. differential line driver/receiver in+ in- v s + v s - out in+ in- v s + v s - out 0.1f +5v 0.1f -5v 250 5 5 250 250 v out v in 0.1f 0.1f +5v -5v el5166 el5166 in+ in- v s + v s - out in+ in- v s + v s - out 0.1f +5v 0.1f -5v 0.1f 0.1f 250 250 250 250 v out v in +5v -5v el5166 el5166 in+ in- v s + v s - out in+ in- v s + v s - out 0.1f +5v 0.1f -5v 250 120 120 250 250 v out + v in 0.1f 0.1f +5v -5v v out - in+ in- v s + v s - out in+ in- v s + v s - out 0.1f +5v 0.1f -5v 250 250 250 v out 0.1f 0.1f +5v -5v 250 1k 1k 240 0.1f 0.1f receiver transmitter el5166 el5166 el5166 el5166 el5166, el5167
13 fn7365.6 september 14, 2010 el5166, el5167 package outline drawing m8.15e 8 lead narrow body small outline plastic package rev 0, 08/09 unless otherwise specified, tolerance : decimal 0.05 the pin #1 identifier may be either a mold or mark feature. interlead flash or protrusions shall not exceed 0.25mm per side. dimension does not include interlead flash or protrusions. dimensions in ( ) for reference only. dimensioning and tolerancing conform to amse y14.5m-1994. 3. 5. 4. 2. dimensions are in millimeters. 1. notes: detail "a" side view ?a typical recommended land pattern top view a b 4 4 0.25 a mc b c 0.10 c 5 id mark pin no.1 (0.35) x 45 seating plane gauge plane 0.25 (5.40) (1.50) 4.90 0.10 3.90 0.10 1.27 0.43 0.076 0.63 0.23 4 4 detail "a" 0.22 0.03 0.175 0.075 1.45 0.1 1.75 max (1.27) (0.60) 6.0 0.20 reference to jedec ms-012. 6. side view ?b?
14 fn7365.6 september 14, 2010 small outline transistor plastic packages (sc70-5) d e 1 e e1 c l c c l e b c l a2 a a1 c l 0.20 (0.008) m 0.10 (0.004) c c -c- seating plane 4 5 123 view c view c l r1 r 4x 1 4x 1 gauge plane l1 seating l2 c plane c base metal with c1 b1 plating b 0.4mm 0.75mm 0.65mm 2.1mm typical recommended land pattern p5.049 5 lead small outline transistor plastic package symbol inches millimeters notes min max min max a 0.031 0.043 0.80 1.10 - a1 0.000 0.004 0.00 0.10 - a2 0.031 0.039 0.80 1.00 - b 0.006 0.012 0.15 0.30 - b1 0.006 0.010 0.15 0.25 c 0.003 0.009 0.08 0.22 6 c1 0.003 0.009 0.08 0.20 6 d 0.073 0.085 1.85 2.15 3 e 0.071 0.094 1.80 2.40 - e1 0.045 0.053 1.15 1.35 3 e 0.0256 ref 0.65 ref - e1 0.0512 ref 1.30 ref - l 0.010 0.018 0.26 0.46 4 l1 0.017 ref. 0.420 ref. - l2 0.006 bsc 0.15 bsc 0 o 8 o 0 o 8 o - n5 55 r 0.004 - 0.10 - r1 0.004 0.010 0.15 0.25 rev. 3 7/07 notes: 1. dimensioning and tolerances per asme y14.5m-1994. 2. package conforms to eiaj sc70 and jedec mo-203aa. 3. dimensions d and e1 are exclusiv e of mold flash, protrusions, or gate burrs. 4. footlength l measured at reference to gauge plane. 5. ?n? is the number of terminal positions. 6. these dimensions apply to the flat section of the lead between 0.08mm and 0.15mm from the lead tip. 7. controlling dimension: millime ter. converted inch dimen- sions are for reference only. el5166, el5167
15 fn7365.6 september 14, 2010 el5166, el5167 package outline drawing p5.064a 5 lead small outline transistor plastic package rev 0, 2/10 dimension is exclusive of mold flash, protrusions or gate burrs. this dimension is measured at datum ?h?. package conforms to jedec mo-178aa. foot length is measured at reference to guage plane. dimensions in ( ) for reference only. dimensioning and tolerancing conform to asme y14.5m-1994. 6. 3. 5. 4. 2. dimensions are in millimeters. 1. notes: detail "x" side view typical recommended land pattern top view index area pin 1 seating plane gauge 0.450.1 (2 plcs) 10 typ 4 1.90 0.40 0.05 2.90 0.95 1.60 2.80 0.05-0.15 1.14 0.15 0.20 c a-b d m (1.20) (0.60) (0.95) (2.40) 0.10 c 0.08-0.20 see detail x 1.45 max (0.60) 0-3 c b a d 3 3 3 0.20 c (1.90) 2x 0.15 c 2x d 0.15 c 2x a-b (0.25) h 5 2 4 5 5 end view plane
16 fn7365.6 september 14, 2010 el5166, el5167 package outline drawing p6.064a 6 lead small outline transistor plastic package rev 0, 2/10 1.60 0.08-0.20 see detail x (0.60) 0-3 3 5 detail "x" side view typical recommended land pattern top view end view index area pin 1 seating plane gauge 0.450.1 (2 plcs) 10 typ 4 1.90 0.40 0.05 2.90 0.95 2.80 0.05-0.15 1.14 0.15 0.20 c a-b d m (1.20) (0.60) (0.95) (2.40) 0.10 c 1.45 max c b a d 3 3 0.20 c (1.90) 2x 0.15 c 2x d 0.15 c 2x a-b (0.25) h 64 5 5 13 2 plane dimension is exclusive of mold flash, protrusions or gate burrs. this dimension is measured at datum ?h?. package conforms to jedec mo-178aa. foot length is measured at reference to guage plane. dimensions in ( ) for reference only. dimensioning and tolerancing conform to asme y14.5m-1994. 6. 3. 5. 4. 2. dimensions are in millimeters. 1. notes:

▲Up To Search▲

Price & Availability of EL5167ICZ-T7

	To Download EL5167ICZ-T7 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .